Hi,

@chimbo : Yes i know about the 20080121_NetworkStorage_R400b2.zip, thats me that asked this one to amit ;o)

About the Upgrade procedure, i've also tried different things, like recovery mode with this file, unmodded.
Everything works.

Tried with your mod with recovery procedure, tftp goes on very fast... too fast... and nothing really hapens, your mod isnt loaded...

This is only about the admin "update firmware" page, seems it doesnt want to load anything...

If somebody updated his MGB111 with the same file and has such problem, let me know.
I've send a mail to AMIT to know if they have seen something like that.

Hard to believe this could be some hardware problem... especially because of nature of the problem itself. Thought maybe if the hardware part was broken, this could cause some other problems, and this one came just after i updated the FW with AMIT one.

[EDIT] tried something, just made a backup of my config, and used the "update / restore backup config" and... this works, it seems it doesnt work only with firmware bin files...

I'm not shure if I understand your question. Added busybox options can be verified in telnet session. Other options by looking at /etc/mini-lpd and /etc/rc.d/rc.bridge.

chimbo

Well, very most of the job has already been done by Amit. All that was left to do is creating the configuration dir /etc/mini-lpd in r/w memory. This is a symlink to /var/config/mini-lpd which is created in /etc/rc.d/rc.bridge. Have a look at the readme in the mini-lpd source dir. The Amit hotplug binary does the rest, that is building the data for mini-lpd and starting it. Unfortunately the amit binary does not recognize all printers which seems to be your problem.
Mini-lpd can be replaced by lpd wich is also handled by Amit. All it needs is adding the lpd binary. Look here

http://www.macsat.com/macsat/compone...g3523/#msg3523

chimbo

Hi ciko,
really have no idea. Also no idea why hdd connected or not should have any influence. All I can imagine is that anything went wrong with download. Try it once again and check size.
chimbo

@ ukez:

Try this, open the mgb, save your datas on another computer using linux, delete all partitions on your hdd, boot your mgb without hdd inside, and use the recovery flash (procedure in german on the stylesuxx blog : http://stylesuxx.twoday.net/stories/4702831/).

After this, put your blank hdd inside, use the mgb options to create partition and format, and try to use again.
There are not printer options on this device, this aint no printer server, you can use some with the mod thats has been posted in this thread but this may not work with every device.

For the airlive firmware, it will probably give you error msg too, not compatible as far as i know.

good luck

The link to stylesuxx blog works for me...

May i ask where did you bought your device? seems some reseller made a mistake...
Or maybe am i wrong, but as far i've seen with original fw, it does not work.

Ok heres what i did to re-flash it.

1. I switched on my MGB111 device

2. Activated the recovery loader by continously holding down the (Shutdown) & (Backup) switch on the MGB111 (this also defaults the device so to anyone else attempting this ensure your ip address on your pc is set to 192.168.123.xxx range).

3. Once the bottom 4 LED's continously flashed together really fast i opened the command prompt, by typing CMD and pushing the enter key in the run option on the start menu.

4. Once the command prompt was open i typed the following C:\>tftp -i 192.168.123.254 PUT C:\IMAGE.BIN, (C:\ being the location of my firmware file & Image.bin being the name of my file).

5. I then pushed enter and run the upload.

6. Then once the following displayed on my screen (Transfer successful: 3873531 bytes in 61 seconds, 63500 bytes/s) i switched off and on my device and that was the firmware update complete.