|
Ernst
|
 |
« Reply #15 on: February 18, 2008, 22:47:40 PM » |
|
@schufti,
Yes, I managed to get smartctl working (even a later version 5.18, everything later than tat is c++ which doesn't compile, or the ./configure doesn't work).
Could you do me a favor and explain about these shell settings? Or point me to a post where this perhaps has already been explained? Thanks!
Ernst
|
|
|
|
|
Logged
|
|
|
|
|
schufti
|
|
« Reply #16 on: February 19, 2008, 08:36:27 AM » |
|
Hi ernst, have a look at this
post. schufti |
|
|
|
|
Logged
|
I won't answer posts or PMs about repair/recovery after bad flash until proven that the wiki was read and followed! find all my MGB100 files here, pass: mgb100 |
|
|
|
xitix
|
|
« Reply #17 on: February 19, 2008, 15:37:25 PM » |
|
@schufti Hello again, thank you for the c03, but unfortunately the FTP doesn't work even after I modified the vsftpd.conf I have removed these lines: enable_iconv=YES remote_charset... local_charset... but with FTP, still not any success  Any othe sugestion? When typing the "amit_tftpd" command, I got the unvariable "bind error" response. Than you. xitix |
|
|
|
« Last Edit: February 19, 2008, 15:39:55 PM by xitix »
|
Logged
|
|
|
|
|
schufti
|
|
« Reply #18 on: February 19, 2008, 19:07:40 PM » |
|
Hi xitix,
to get ftp you have to start vsftpd ....
schufti
|
|
|
|
|
Logged
|
I won't answer posts or PMs about repair/recovery after bad flash until proven that the wiki was read and followed! find all my MGB100 files here, pass: mgb100 |
|
|
|
xitix
|
|
« Reply #19 on: February 20, 2008, 10:10:35 AM » |
|
Hi Schufti, thank you for the FTP trick !  Now I can study the "busybox inside" in midnight commander... Anyway, after restarting the box, the vsftpd.conf apear in the old form, including the "enable_iconv=YES", "local_charset=UTF-8" and "remote_charset=UTF-8" lines. Replacing the vsftpd.conf can be done forever, or I have to edit the vsftpd.conf from /etc and /var/config + restart the vsftpd any time I reset the box? ok, other oservations:1) With c03FW + download-manager GUI, the errors when resume the one torrent track are gone. 2) Still, the inconvenient with change manually the BT.BCP.value (port number) from ./btc.htm before resume each torrent from private servers (with proxy), otherwise got the "invalid port number". Is there any possibility to store somehow the BT.BCP.value for each torrent track? 3) After restarting the vsftpd, the ftp log is reported corectly! 4) I confirm that disk status is reported incorrcetly in ./more.htm Thank you again! xitix |
|
|
|
« Last Edit: February 20, 2008, 14:40:04 PM by xitix »
|
Logged
|
|
|
|
|
haixiao
|
|
« Reply #20 on: June 01, 2008, 05:00:18 AM » |
|
where can i found the web gui source code?
|
|
|
|
|
Logged
|
|
|
|
|
my2002
|
|
« Reply #21 on: August 31, 2008, 16:57:25 PM » |
|
hi. I have a SMCWAPS-G. Can I flash my SMCWAPS-G with MGB100_400S07.upg? If it's OK,Can you emailz(MGB100_400S07.upg) to me? My email is maytangy@hotmail.com. Thank for your help! |
|
|
|
|
Logged
|
|
|
|
|
stharvey
|
|
« Reply #22 on: October 17, 2008, 16:19:25 PM » |
|
Hi,
I have a SMC version of this box which was running the latest WMU-6000FS firmware from airlive.
I was having a few problems with it so decided to try your firmware (MGB100_400S07.upg)
I upgraded and was told the upgrade was successful however after reboot the device seems to have stopped working. The power light is on and the ethernet light comes on when the cable is plugged in but apart from that not a lot is happening. The buttons don't seem to be functioning and I can't access the web interface.
Any suggestions?
Cheers,
Sam
|
|
|
|
|
Logged
|
|
|
|
|
schufti
|
|
« Reply #23 on: October 17, 2008, 17:51:50 PM » |
|
Hi, as you could have read here, that is perfectly normal if you do things that are not expected (= downgrade fw). the title says it all: for old GUI (w/o download manager) so, definitely not for latest WMU-6000FS (V400c3) schufti |
|
|
|
« Last Edit: October 17, 2008, 17:53:59 PM by schufti »
|
Logged
|
I won't answer posts or PMs about repair/recovery after bad flash until proven that the wiki was read and followed! find all my MGB100 files here, pass: mgb100 |
|
|
|
stharvey
|
|
« Reply #24 on: October 17, 2008, 18:39:53 PM » |
|
Ah... ooops, I somehow missed that page.
Is this fatal? Is there any kind of remedy or is the device useless now?
Cheers,
Sam
|
|
|
|
|
Logged
|
|
|
|
|
schufti
|
|
« Reply #25 on: October 17, 2008, 23:08:35 PM » |
|
I won't answer posts or PMs about repair/recovery after bad flash until proven that the wiki was read and followed!
|
|
|
|
|
Logged
|
I won't answer posts or PMs about repair/recovery after bad flash until proven that the wiki was read and followed! find all my MGB100 files here, pass: mgb100 |
|
|
|
stharvey
|
|
« Reply #26 on: October 18, 2008, 01:08:53 AM » |
|
Thanks for your help.
Sorry for the simple questions but this is fairly new to me.
Where do I find an original firmware .bin file? I have tried the firmware files on the airlive site but they all seem to be upgrades and do not work. I have searched for R400b7.BIN but cannot find it on the net - the only links do not work.
Any help would be really appreciated.
Thank you very much
Sam
|
|
|
|
|
Logged
|
|
|
|
|
schufti
|
|
« Reply #27 on: October 18, 2008, 08:09:03 AM » |
|
as I don't know what you did with your box, I cant say what fw you really need.
you are saying that you have a SMC box, but you were working with tha latest airlive fw!
what didi you do to get that working? Did you use the "opening" fw, did you rebrand with my "rebranding" files or ....?
No fw on the airlive website is an upgrade file, they are all full fw.
but if it is still SMC "inside" (what I doubt) then you'll need SMC fw!
btw, did you manage to start recovery loader?
schufti
|
|
|
|
|
Logged
|
I won't answer posts or PMs about repair/recovery after bad flash until proven that the wiki was read and followed! find all my MGB100 files here, pass: mgb100 |
|
|
|
|
|
schufti
|
|
« Reply #29 on: October 18, 2008, 17:00:09 PM » |
|
hi stharvey,
now it is starting to make sense...
Best thing for you to do isget the "rebranding" package from the wiki/repository. Then flash your box with the file "ovislink.bin" via recovery loader. Right after this (without reboot) flash the v400b6 fw from the airlive page. Then you should reboot and reset to factory settings. After this you can decide to work with old GUI and S8 (GPL-) upgrade file or flash to latest original c3 airlive fw with new GUI (download agent) and then "upgrade" with my c4 (GPL-)upgrade file.
N.B.: "uprade" files don't come with GUI, so one has to use orig fw files to successfully upgrade between all orig fw versions. (GPL-)upgrade files are allways valid for same base orig. fw version only.
schufti
|
|
|
|
|
Logged
|
I won't answer posts or PMs about repair/recovery after bad flash until proven that the wiki was read and followed! find all my MGB100 files here, pass: mgb100 |
|
|
|
